Denon DN-S 1200

HOW TO SET UP?

The system must recognize your Denon DN S 1200 device/s before configuring in DJ ProMixer.
IMPORTANT: Denon DN S 1200 is a MIDI and audio sound card device
Download and install DENON DJ ASIO Driver

DJ ProMixer Denon ASIO Panel

MIDI CONFIGURATION

Single Mode (2 Denon S 1200 Connected)

DJ ProMixer MIDI Denon DN S 1200 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one device (Denon DN S 1200 0) and select on the right side DENON DN S 1200 (SINGLE A).XML. Select in MIDI PORT / MIDI MAP 2 on the left side the other device (Denon DN S 1200 I) and select on the right side DENON DN S 1200 (SINGLE B).XML

Dual Mode

DJ ProMixer MIDI Denon DN S 1200 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side Numark DENON DN S 12000, and select on the right side DENON DN S 1200 (A AND B).XML. Nothing selected in MIDI PORT / MIDI MAP 2 How to change the decks? Two ways: 1.- Hardware: Use the “Single Button”. 2.- Software: By clicking the headphone button of the deck.

AUDIO CONFIGURATION

DJ ProMixer ASIO Denon DN S 1200

Open DJ ProMixer and go to “Config”, open “Audio Setup”, here you can select your Denon DN S 1200 as Audio Sound Card.
IMPORTANT: Denon DN S 1200 works with ASIO Driver, also it can be used with Direct Sound Driver Mode.

MIDI MAP

DJ ProMixer Denon S 1200 map

1.-   PLAY / PAUSE
2.-   CUE
 
3.-   SYNC
 
4.-   MANUAL LOOP: IN
5.-   MANUAL LOOP: OUT
6.-   AUTO LOOP: 1/2
7.-   AUTO LOOP: 2X
8.-   EXIT / RELOOP
9.-   FX 1: ECHO
10.- FX 2: FLANGER
11.- FX 3: WAH

12.- MEMORY CUE / LOOP
13.- SEARCH MODE
14.- SCROLL
15.- PUSH: LOAD / ENTER
16.- CHANGE FOCUS TREE / TRACKLIST

17.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER 
18.- PITCH

19.- KEYLOCK
20.- PITCH BEND (BUTTONS)
21.- SCRATCH MODE (WHEEL)
22.- BEND (WHEEL)
23.- BRAKE
24.- REVERSE
25.- DECK SELECTOR (DECK A / DECK B) (ONLY DUAL MODE)
27.- LINK TO PC (SOURCE)

info mapping                    info PDF

Advertisements

Numark Mixtrack / Pro III

HOW TO SET UP?

The system must recognize your Numark Mixtrack / Pro III as Audio Device before configuring in DJ ProMixer.

AUDIO SETTINGS

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Mixtrack Pro III as Audio Sound Card.
Note: You do not need install additionals audio drivers, once connected is just plug and play.

DJ ProMixer Numark Mixtrack Pro 3 Audio

Connect your output in (1) RCA  connectors (L+R) for Master Output.

Connect your headphones in front ( ¼ TSR stereo connector).

Important: Numark Mixtrack Pro is designed to be used as internal mode (with internal Sound Card using master output  & headphones) or external mode (using the internal soundcard for each deck).

MIDI SET UP

DJ ProMixer Numark Mixtrack Pro 3 MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MixTrack / Pro III) and select on the right side NUMARK MIXTRACK PRO III.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview
DJ ProMixer Numark Mixtrack Pro III map
(Click to enlarge)

Detail

DJ ProMixer Numark Mixtrack Pro III map detail

 

1.-   PLAY / PAUSE
2.-   CUE
3.-   SYNC
4.-   SHIFT SELECTOR
5.-   ENABLE WHEEL VINYL MODE
6.-   NEEDLE SEARCH
7.-   BEND (BUTTONS)
8.-   PITCH
9.-   FX 1 (ECHO)
10.- FX 2 (FLANGER)
11.- FX 3 (WAH)
12.- FX DRY / WET
13.- (SHIFT +) FX PARAMETER
14.- PAD MODE SELECTOR
15.- PAD MODE SELECTOR + MANUAL LOOP PAD = ENABLE MANUAL LOOP
PAD 1 = LOOP IN / PAD 2 = LOOP OUT / PAD 3 = EXIT / RELOOP
16.- PAD MODE SELECTOR + AUTOLOOP = ENABLE AUTOLOOP
PAD 2 = 1/2 LOOP / PAD 3 = EXIT / RELOOP / PAD 4 = 2X LOOP
17.- PAD MODE SELECTOR + SAMPLER = ENABLE SAMPLER
PAD 1 = SAMPLE 1 / PAD 2 = SAMPLE 2 / PAD 3 = SAMPLE 3 / PAD 4 = SAMPLE 4
18.- CUE PAD: CUE 1 / CUE 2 / CUE 3 / CUE 4
19.- ROTARY KNOBS OF THE MIXER (HI, MID,BASS)
20.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

21.- HEADPHONES VOLUMEN (A / B)
22.- PFL
23.- TRACKLIST SCROLL
24.- CHANGE FOCUS TREE / TRACKLIST
25.- (SHIFT + PUSH) OPEN PLAYLIST
26.- LOAD DECK A / B
27.- BEND (WHEEL)
28.- SCRATCH

PAD MODE DETAIL

DJ ProMixer MIDI Mixtrack 3 PAD mode detail

info mapping                    info PDF

Hercules DJ Control Instinct S

HOW TO SET UP?

The system must recognize your Hercules DJ Control Instinct S as Audio and MIDI device before configuring in DJ ProMixer.

Hercules DJ Control Instinct S only requires download and install Hercules ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Hercules DJ Control Instinct S as Audio Sound Card.

DJ ProMixer ASIO Hercules DJ 4Set

MIDI SET UP

DJ ProMixer MIDI Hercules DJ Control Instinct S

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (HERCULES DJ CONTROL INSTINCTS0) and select on the right side HERCULES DJ CONTROL INSTINCT S.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Hercules DJ Control Instinct S map

Detail

 DJ ProMixer Hercules DJ Control Instinct S map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    PAD MODE (NOTHING SELECTED) MEMORY CUE/LOOP: PAD 1 – CUE/LOOP 1, PAD 2 – CUE/LOOP 2, PAD 3 – CUE-LOOP 3, PAD 4 – CUE-LOOP 4
8.-    PAD MODE (LOOP SELECTED):
PAD 1 – 1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 2 – X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 3 – MANUAL LOOP: IN
PAD 4 – MANUAL LOOP: OUT / EXIT / RELOOP

9.-   PAD MODE (FX SELECTED): PAD 1 – FX 1 (ECHO), PAD 2 – FX 2 (FLANGER), PAD 3 – FX 3 (WAH)
10.-  PAD MODE (SAMPLER SELECTED): PAD 1 – SAMPLE 1, PAD 2 – SAMPLE 2, PAD 3 – SAMPLE 3, PAD 4 – SAMPLE 4
11.-  BEND (WHEEL)
12.-  SCRATCH
13.-  PAD MODE SELECTOR: (7) NOTHING SELECTED: MEMORY CUE/LOOP – (8) LOOP (AUTO/MANUAL) – (9) FX – (10) SAMPLER MODE
14.-  VINYL MODE
15.-  FOLDER-TREE SELECTOR / OPEN CLOSE
16.-  TRACKLIST SELECTOR
17.- TRACKLIST MOVE UP
18.- TRACKLIST MOVE DOWN

19-   LOAD DECK
20-   PFL
21-   ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS) 
22.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Hercules DJ Control Air S

HOW TO SET UP?

The system must recognize your Hercules DJ Control Air S as Audio and MIDI device before configuring in DJ ProMixer.

Hercules DJ Control Air S only requires download and install Hercules ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Hercules DJ Control Air S as Audio Sound Card.

DJ ProMixer ASIO Hercules DJ 4Set

MIDI SET UP

DJ ProMixer MIDI Hercules DJ Control Air S

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DJ CONTROL AIRS0) and select on the right side HERCULES DJ CONTROL AIR S.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Hercules DJ Control Air S map

Detail

 DJ ProMixer Hercules DJ Control Air S map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    PAD MODE (NOTHING SELECTED) MEMORY CUE/LOOP: PAD 1 – CUE/LOOP 1, PAD 2 – CUE/LOOP 2, PAD 3 – CUE-LOOP 3, PAD 4 – CUE-LOOP 4
8.-    PAD MODE (LOOP SELECTED):
PAD 1 – 1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 2 – X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 3 – MANUAL LOOP: IN
PAD 4 – MANUAL LOOP: OUT / EXIT / RELOOP

9.-   PAD MODE (FX SELECTED): PAD 1 – FX 1 (ECHO), PAD 2 – FX 2 (FLANGER), PAD 3 – FX 3 (WAH)
10.-  PAD MODE (SAMPLER SELECTED): PAD 1 – SAMPLE 1, PAD 2 – SAMPLE 2, PAD 3 – SAMPLE 3, PAD 4 – SAMPLE 4
11.-  PAD MODE SELECTOR: (8) LOOP (AUTO/MANUAL)
12.-  PAD MODE SELECTOR: (9) FX
13.-  PAD MODE SELECTOR: (10) SAMPLER MODE
14.-  BEND (WHEEL)
15.-  SRATCH

16.-  FOLDER-TREE SELECTOR / OPEN CLOSE
17.-  TRACKLIST SELECTOR
18.-  TRACKLIST MOVE UP
19.-  TRACKLIST MOVE DOWN
20-   LOAD DECK
21-   PFL
22.-  VINYL MODE
23.-  REC
24.-  AIR CONTROL (FX DRY/WET)
25-   ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS) 
26.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

IMPORTANT:
DJ ProMixer Hercules Air Control_1
Air Control enables FX Dry/Wet control (24) for booth Decks

info mapping                    info PDF

Hercules DJ Control Air

HOW TO SET UP?

The system must recognize your Hercules DJ Control Air as Audio and MIDI device before configuring in DJ ProMixer.

Hercules DJ Control Air only requires download and install Hercules ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Hercules DJ Control Air as Audio Sound Card.

DJ ProMixer ASIO Hercules DJ 4Set

MIDI SET UP

DJ ProMixer MIDI Hercules DJ Control Air

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DJ CONTROL AIR0) and select on the right side HERCULES DJ CONTROL AIR.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Hercules DJ Control Air map

Detail

 Hercules DJ Control Air map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    PAD MODE (NOTHING SELECTED) MEMORY CUE/LOOP: PAD 1 – CUE/LOOP 1, PAD 2 – CUE/LOOP 2, PAD 3 – CUE-LOOP 3, PAD 4 – CUE-LOOP 4
8.-    PAD MODE (LOOP SELECTED):
PAD 1 – 1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 2 – X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 3 – MANUAL LOOP: IN
PAD 4 – MANUAL LOOP: OUT / EXIT / RELOOP

9.-   PAD MODE (FX SELECTED): PAD 1 – FX 1 (ECHO), PAD 2 – FX 2 (FLANGER), PAD 3 – FX 3 (WAH)
10.-  PAD MODE (SAMPLER SELECTED): PAD 1 – SAMPLE 1, PAD 2 – SAMPLE 2, PAD 3 – SAMPLE 3, PAD 4 – SAMPLE 4
11.-  PAD MODE SELECTOR: (8) LOOP (AUTO/MANUAL)
12.-  PAD MODE SELECTOR: (9) FX
13.-  PAD MODE SELECTOR: (10) SAMPLER MODE
14.-  BEND (WHEEL)
15.-  SRATCH

16.-  FOLDER-TREE SELECTOR / OPEN CLOSE
17.-  TRACKLIST SELECTOR
18.-  TRACKLIST MOVE UP
19.-  TRACKLIST MOVE DOWN
20-   LOAD DECK
21-   PFL
22.-  VINYL MODE
23.-  REC
24.-  AIR CONTROL (FX DRY/WET)
25-   ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS) 
26.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

IMPORTANT:
DJ ProMixer Hercules Air Control_1
Air Control enables FX Dry/Wet control (24) for booth Decks

info mapping                    info PDF

Hercules DJ Control Instinct

HOW TO SET UP?

The system must recognize your Hercules DJ Control Instinct as Audio and MIDI device before configuring in DJ ProMixer.

Hercules DJ Control Instinct only requires download and install Hercules ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Hercules DJ Control Instinct as Audio Sound Card.

DJ ProMixer ASIO Hercules DJ 4Set

MIDI SET UP

DJ ProMixer MIDI Hercules DJ Control Instinct

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (HERCULES DJ CONTROL INSTINCT0) and select on the right side HERCULES DJ CONTROL INSTINCT.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Hercules DJ Control Instinct map

Detail

 DJ ProMixer Hercules DJ Control Instinct map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    PAD MODE (NOTHING SELECTED) MEMORY CUE/LOOP: PAD 1 – CUE/LOOP 1, PAD 2 – CUE/LOOP 2, PAD 3 – CUE-LOOP 3, PAD 4 – CUE-LOOP 4
8.-    PAD MODE (LOOP SELECTED):
PAD 1 – 1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 2 – X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
PAD 3 – MANUAL LOOP: IN
PAD 4 – MANUAL LOOP: OUT / EXIT / RELOOP

9.-   PAD MODE (FX SELECTED): PAD 1 – FX 1 (ECHO), PAD 2 – FX 2 (FLANGER), PAD 3 – FX 3 (WAH)
10.-  PAD MODE (SAMPLER SELECTED): PAD 1 – SAMPLE 1, PAD 2 – SAMPLE 2, PAD 3 – SAMPLE 3, PAD 4 – SAMPLE 4
11.-  BEND (WHEEL)
12.-  SCRATCH
13.-  PAD MODE SELECTOR: (7) NOTHING SELECTED: MEMORY CUE/LOOP – (8) LOOP (AUTO/MANUAL) – (9) FX – (10) SAMPLER MODE
14.-  VINYL MODE
15.-  FOLDER-TREE SELECTOR / OPEN CLOSE
16.-  TRACKLIST SELECTOR
17.-  TRACKLIST MOVE UP
18.-  TRACKLIST MOVE DOWN

19-   LOAD DECK
20-   PFL
21-   ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS) 
22.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Hercules DJ 4Set

HOW TO SET UP?

The system must recognize your Hercules DJ 4 Set as Audio and MIDI device before configuring in DJ ProMixer.

Hercules DJ 4 Set only requires download and install Hercules ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Hercules DJ 4 Set as Audio Sound Card.

DJ ProMixer ASIO Hercules DJ 4Set

MIDI SET UP

DJ ProMixer MIDI Hercules DJ 4Set

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (HERCULES DJ 4 SET MID0) and select on the right side HERCULES DJ 4 SET.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Hercules DJ 4Set map

Detail

 DJ ProMixer Hercules DJ 4Set map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
8.-    X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
9.-    (SHIFT) ENABLE / DISABLE FX DIRECT BUTTONS
10.-  NOTHING SELECTED: MANUAL LOOP IN / OUT-EXIT-RELOOP
11.-  (SHIFT ENABLED) FX DIRECT BUTTONS (FX 1: ECHO, FX2 : FLANGER, FX3 : WAH)
12.-  BEND (WHEEL)
13.-  SCRATCH
14.-  PFL
15.-  FOLDER-TREE SELECTOR / OPEN CLOSE
16.-  TRACKLIST SELECTOR
17.- TRACKLIST MOVE UP
18.- TRACKLIST MOVE DOWN

19-   LOAD DECK
20-   VINYL MODE
21-   REC
22-   ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS) 
23.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Akiyama TTWO

HOW TO SET UP?

The system must recognize your Akiyama TTWO as Audio and MIDI device before configuring in DJ ProMixer.

Akiyama TTWO only requires download and install TTWO Akiyama ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Akiyama TTWO as Audio Sound Card.

DJ ProMixer ASIO Akiyama TTWO

 

DJ ProMixer Akiyama TTWO Audio Connections

For Internal Mode choose your output: 1.- for 1/4 TRS connectors (balanced)  or 2.- for RCA (unbalanced) (1+2).

MIDI SET UP

DJ ProMixer MIDI Akiyama TTWO

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (AKIYAMA TTWO0) and select on the right side AKIYAMA TTWO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Akiyama TTWO map

Detail

 DJ ProMixer Akiyama TTWO map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    VINYL MODE
5.-    PITCH
6.-    BEND (BUTTONS)
7.-    FX DRY / WET
8.-    FX PARAMETER
9.-    FX ECHO SYNC (FROM 2/1 TO 1/8 BEATS)
10.-  SAMPLER DIRECT BUTTONS SELECTOR
11.-  NOTHING SELECTED: MEMORY CUE / LOOP DIRECT BUTTONS (1, 2, 3, 4)
12.-  SAMPLER SELECTOR ENABLED: SAMPLER DIRECT BUTTONS (1, 2, 3, 4)
13.-  (SHIFT +) FX DIRECT BUTTONS (FX 1: ECHO, FX2 : FLANGER, FX3 : WAH)
14.-  MANUAL LOOP: IN / OUT-EXIT-RELOOP
15.-  1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
16.-  X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
17.-  PFL
18.-  BEND (WHEEL)
19-  SCRATCH
20-  SHIFT
21-  LOAD DECK
22-  SCROLL: TRACKLIST
23.- (SHIFT +) SCROLL: TREE
24.- ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS +PUSH KILL), GAIN
25.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Akiyama Quattro

HOW TO SET UP?

The system must recognize your Akiyama Quattro as Audio and MIDI device before configuring in DJ ProMixer.

Akiyama Quattro only requires download and install Akiyama Quattro ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Akiyama Quattro as Audio Sound Card.

DJ ProMixer ASIO Akiyama Quattro

DJ ProMixer Akiyama Quattro Audio Connections_1

For Internal Mode choose your output: 1.- for XLR connectors (balanced)  or 2.- for RCA (unbalanced) (1+2).

MIDI SET UP

DJ ProMixer MIDI Akiyama Quattro

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (AKIYAMA QUATRO0) and select on the right side AKIYAMA QUATTRO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Akiyama Quattro map

Detail

DJ ProMixer Akiyama Quattro map detail


1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    KEYLOCK
5.-    VINYL MODE
6.-    PITCH
7.-    BEND (BUTTONS)
8.-    FX DRY / WET
9.-    FX PARAMETER
10.-  FX ECHO SYNC (FROM 2/1 TO 1/8 BEATS)
11.-  FX DIRECT BUTTONS (FX 1: ECHO, FX2 : FLANGER, FX3 : WAH)
12.-  (SHIFT +) SAMPLER DIRECT BUTTONS (1, 2, 3, 4)
13.-  MEMORY CUE / LOOP DIRECT BUTTONS (1, 2, 3, 4)
14.-  MANUAL LOOP: IN / OUT-EXIT-RELOOP
15.-  1/2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
16.-  X2 AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
17.-  PFL
18.-  BEND (WHEEL)
19-  SCRATCH
20-  SHIFT
21-  OPEN / CLOSE FOLDER
22-  SCROLL: TRACKLIST
23.- (SHIFT +) SCROLL: TREE
24.- LOAD DECK
25.- ROTARY KNOBS OF THE MIXER (EQ HI, MID,BASS +PUSH KILL), GAIN
26.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

American Audio VMS 4.1

HOW TO SET UP?

The system must to recognize your American Audio VMS 4.1 as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO SETTINGS

American Audio VMS 4.1 only requires download and install ADJ Asio Driver.

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your American Audio VMS  4.1 as Audio Sound Card.

DJ ProMixer American Audio VMS 41 ASIO

DJ ProMixer American Audio VMS 41 Audio Connection

For Internal Mode choose your output: 1.- for XLR connectors (balanced)  or 2.- for RCA (unbalanced).

Important: American Audio VMS 4.1 is designed to be used in internal mode (with internal Sound Card), but you can use also with DJ ProMixer in external mode (with other/s Sound Card/s and external mixer).

American Audio VMS 4.1 has two different MIDI maps:
1.- (Mode 1) (Using touchpads)
2.- (Mode 2) (Without touchpads)

MIDI CONFIGURATION

Mode 1

DJ ProMixer American Audio VMS 41 MID Map 1

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (VMS410) and select on the right side AMERICAN AUDIO VMS4-1.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP 1 (Overview)

DJ ProMixer American Audio VMS 41 map1

Detail

DJ PorMixer American Audio VMS 41 map1_detail

1.-   PLAY
2.-   PAUSE

3.-   CUE
4.-   SYNC
5.-   (SHIFT +) CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
6.-   BEND (BUTTONS)
7.-   FX PARAMETER

8.-   FX DRY / WET
9.-   FX ECHO SYNC (FROM 2/1 TO 1/8 BEATS)
10.- FX 1 (ECHO)
11.- FX 2 (FLANGER)
12.- FX 3 (WAH)
13.- MANUAL LOOP IN
14.- MANUAL LOOP OUT / EXIT / RELOOP
15.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) 1/2
16.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) X 2 BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS

17.- SHIFT
18.- ENABLE VINYL MODE
19.- (SHIFT +) KEYLOCK
20.- MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
21.- MEMORY CUE / LOOP (1, 2, 3, 4)
22.- (SHIFT +) SAMPLES (1, 2, 3, 4)
23.- PITCH
24.- TOUCHPAD: TREE SCROLL
25.- SHIFT + TOUCHPAD: TRACKLIST SCROLL
26.- BEND (WHEEL)
27.- SCRATCH
28.- (SHIFT +) LOAD DECK
29.- (SHIFT +) TOUCHPAD: MOUSE
30.- PFL
31.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
32.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

Mode 2

DJ ProMixer American Audio VMS 41 MID Map 2

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (VMS410) and select on the right side AMERICAN AUDIO VMS4-1 V2.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP 2 (Overview)

DJ ProMixer American Audio VMS 41 map2

Detail

DJ ProMixer American Audio VMS 41 map2_detail

1.-   PLAY
2.-   PAUSE
3.-   CUE
4.-   SYNC
5.-   (SHIFT +) CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
6.-   BEND (BUTTONS)
7.-   TRACKLIST SCROLL 

8.-   (SHIFT +) TREE SCROLL
9.-   FX DRY / WET
10.- FX PARAMETER
11.- FX ECHO SYNC (FROM 2/1 TO 1/8 BEATS)
12.- LOAD DECK FX 3 (WAH)
13.- FX 1 (ECHO)
14.- FX 2 (FLANGER)
15.- FX 3 (WAH)
16.- MANUAL LOOP IN
17.- MANUAL LOOP OUT / EXIT / RELOOP
18.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) 1/2
19.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) X 2 BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS

20.- SHIFT
21.- MEMORY CUE / LOOP (1, 2, 3, 4)
22.- (SHIFT +) SAMPLES (1, 2, 3, 4)
23.- PITCH
24.- ENABLE VINYL MODE
25.- (SHIFT +) KEYLOCK

26.- BEND (WHEEL)
27.- SCRATCH
28.- MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
29.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
30.- PFL
31.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Numark Mixtrack Edge

HOW TO SET UP? The system must recognize your Numark Mixtrack Edge as Audio and MIDI Device before configuring in DJ ProMixer.

AUDIO SETTINGS

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Numark Mixtrack Edge as Audio Sound Card. Note: You do not need install additionals audio drivers, once connected is just plug and play. DJ ProMixer Audio Mixtrack Edge Connect your output  (1/8 TSR stereo connector) in Master Output. Connect your headphones in  1/8 TSR headphones stereo connector.

MIDI SET UP

DJ ProMixer MIDI Mixtrack Edge In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MixTrack Edge) and select on the right side NUMARK MIXTRACK EDGE.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview DJ ProMixer Mixtrack-Edge map (Click to enlarge)

Detail

DJ ProMixer Mixtrack-Edge map_detail 1.-    PLAY / PAUSE
2.-    CUE
3.-    SYNC
4.-    (SHIFT +) KEYLOCK
5.-    SHIFT SELECTOR
6.-    FX SELECTOR
7.-    CUE / LOOP MEMORY
8.-    SAMPLES (1,2,3)
9.-    (FX SELECTOR +) FX 1, FX 2, FX 3
10.-  MANUAL LOOP (LOOP IN / OUT / EXIT-RELOOP)
11.-  (SHIFT +) AUTO LOOP (IN 4 BEATS): 1/2 , X2, EXIT-RELOOP
12.-  CHANGE FOCUS TREE / TRACKLIST
13.-  ENTER / PUSH
14.-  HEADPHONES VOLUMEN (A AND B)
15.-  EQ. TREBLE
16.-  EQ. BASS
17.-  (FX SELECTOR) FX DRY / WET
18.-  (FX SELECTOR) FX PARAMETER
19.-  WHEEL: BEND
20.-  WHEEL: SCRATCH / (FX SELECTOR) SCRATCH
21.-  WHEEL: MOVE UP / DOWN PITCH
22.-  WHEEL: SEARCH MODE
23.-  PFL
24.-  LOAD DECK
25.-  WHEEL
26.-  DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Numark NDX 500

HOW TO SET UP?

The system must recognize your Numark NDX-500 device/s before configuring in DJ ProMixer.
IMPORTANT: Numark NDX-500 is a MIDI and audio sound card device

MIDI CONFIGURATION

Single Mode (2 Numark NDX-500 Connected)

DJ ProMixer Single Numark NDX 500

Select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark NDX500 0) and select on the right side NUMARK NDX-500(SINGLE A).XML. Select in MIDI PORT / MIDI MAP 2 on the left side the other device (Numark NDX500 I) and select on the right side NUMARK NDX-500(SINGLE B).XML

Dual Mode

DJ ProMixer Dual Numark NDX 500

Select in MIDI PORT / MIDI MAP 1 on the left side Numark NDX500 0, and select on the right side NUMARK NDX-500 (A AND B).XML. Nothing selected in MIDI PORT / MIDI MAP 2 How to change the decks? Two ways: 1.- Hardware: Use the “Single Button”. 2.- Software: By clicking the headphone button of the deck.

AUDIO CONFIGURATION

Open DJ ProMixer and go to “Config”, open “Audio Setup”, here you can select your Numark NDX-500 as Audio Sound Card.

DJ ProMixer Audio Numark NDX 500

MIDI MAP

DJ ProMixer Numark NDX 500 Map

1.-   PLAY / PAUSE
2.-   CUE
 
3.-   SYNC
 
4.-   SCROLL / LOAD / ENTER
5.-   CHANGE FOCUS TREE / TRACKLIST
6.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
7.-   CUE / LOOP MEMORY (1, 2, 3) 

8.-   MEMORIZE CUE / LOOP
9.-   BRAKE
10.- REVERSE
11.- SCRATCH MODE (WHEEL)
12.- SEARCH MODE (WHEEL)
13.- DECK SELECTOR (DECK A / DECK B) (ONLY DUAL MODE)
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER 
15.- PITCH

16.- PITCH BEND
17.- PITCH
18.- BEND (BUTTONS)
19.- BEND (WHEEL)
20.- WHEEL
21.- LINK TO PC (SOURCE)

info mapping                    info PDF

Zomo MC-1000

HOW TO SET UP?

The system must recognize your Zomo MC-1000 as Audio Device and MIDI Device  before configuring in DJ ProMixer.

AUDIO SETTINGS

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Zomo MC-1000 as Audio Sound Card.
Note: You do not need install additionals audio drivers, once connected is just plug and play.

DJ ProMixer Audio Zomo MC - 1000

Connect your output in RCA  connectors for Channels 1+2 (Deck A) and 3+4 (Deck B).

DJ ProMixer Zomo Audio Output

MIDI SET UP

Important: Select “C1” in MIDI Selector

Zomo C1 MIDI Selector

DJ ProMixer MIDI Zomo MC - 1000

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MC-1000) and select on the right side ZOMO MC-1000.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview
DJ ProMixer Zomo MC-1000_map
(Click to enlarge)

Detail

DJ ProMixer Zomo MC-1000_map_detail

1.-   PLAY / PAUSE
2.-   CUE 1, CUE 2, CUE 3
2.-   (SHIFT) CUE 4, MEMO, DEL
3.-   SYNC
4.-   SHIFT SELECTOR
5.-   AUTO LOOP (IN 4 BEAT) IN / OUT / EXIT / RELOOP
6.-   PITCH
7.-   DECK VOLUMEN
8.-   BEND
9.-   FX DRY / WET
9.-   (SHIFT) EQ BASS
10.- FX PARAMETER
10.- (SHIFT) EQ MID
11.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- (SHIFT) EQ HI
12.- (SHIFT) GAIN
13.- FX 1 (ECHO)
13.- (SHIFT) SAMPLE 1
14.- FX 2 (FLANGER)
14.- (SHIFT) SAMPLE 2
15.- FX 3 (WAH)
15.- (SHIFT) SAMPLE 3
16.- PFL
16.- (SHIFT) SAMPLE 4
17.- SCROLL
18.- CHANGE FOCUS TREE / TRACKLIST
19.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
20.- LOAD 

info mapping                    info PDF

Behringer BCD-2000

HOW TO SET UP?

The system must recognize your Behringer BCD-2000 as Audio and MIDI device before configuring in DJ ProMixer.

Behringer BCD-2000  only requires download and install Behringer ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Behringer BCD-2000 as Audio Sound Card.

AUDIO SETTINGS

INTERNAL MODE (Master + Headphones)

 

DJ ProMixer ASIO Behringer BCD-2000

MIDI SET UP

 DJ ProMixer MIDI Behringer BCD-2000

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (BCD30000) and select on the right side BEHRINGER BCD-2000.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

 DJ ProMixer Behringer BCD-2000 Map

Detail

DJ ProMixer Behringer BCD-2000 Map Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   AUTOLOOP (4 BEATS) IN / EXIT
4.-   RELOOP
5.-   SYNC
6.-   SRATCH (WHEEL)
7.-   LOAD TRACK
8.-   BEND (DECK PLAYING) / TRACK SELECTOR (DECK STOPPED)
9.-   PITCH
10.- SELECTOR MEMORY CUE / LOOP
11.- DECK VOLUMEN
12.- EQUALIZER ROTARY KNOBS (GAIN, HI, MID,BASS)
13.- KILL
14.- PFL SELECTOR
15.- FX ECHO
16.- FX FLANGER
17.- FX DRY / WET
18.- FX PARAMETER
19-  WHEEL
20-  CROSSFADER

info mapping                    info PDF

Behringer BCD-3000

HOW TO SET UP?

The system must recognize your Behringer BCD-3000 as Audio and MIDI device before configuring in DJ ProMixer.

Behringer BCD-3000  only requires download and install Behringer ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Behringer BCD-3000 as Audio Sound Card.

AUDIO SETTINGS

INTERNAL MODE (Master + Headphones)

DJ ProMixer ASIO Behringer BCD-3000_

 

MIDI SET UP

 DJ ProMixer MIDI Behringer BCD-3000

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (BCD30000) and select on the right side BEHRINGER BCD-3000.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

 DJ ProMixer BehringerBCD3000 Map

Detail

DJ ProMixer BehringerBCD3000_Map Detail


1.-   PLAY / PAUSE
2.-   CUE
3.-   AUTOLOOP (4 BEATS) IN / EXIT
4.-   RELOOP
5.-   SYNC
6.-   SRATCH (WHEEL)
7.-   LOAD TRACK
8.-   BEND (DECK PLAYING) / TRACK SELECTOR (DECK STOPPED)
9.-   PITCH
10.- SELECTOR MEMORY CUE / LOOP
11.- DECK VOLUMEN
12.- EQUALIZER ROTARY KNOBS (GAIN, HI, MID,BASS)
13.- KILL
14.- PFL SELECTOR
15.- FX ECHO
16.- FX FLANGER
17.- FX DRY / WET
18.- FX PARAMETER
19-  WHEEL
20-  CROSSFADER

info mapping                    info PDF

Numark Omni Control

HOW TO SET UP?

The system must recognize your Numark Omni Control as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURATION

Numark Omni control requires download and install Numark Asio Driver.

DJ ProMixer ASIO Numark Omni Control

This controller has two different configurations (for Internal or External Mode):

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Mixtrack Pro as Audio Sound Card.

AUDIO SETTINGS

INTERNAL MODE (Master + Headphones)

DJ ProMixer Numark Omni Control ASIO Internal

DJ ProMixer Numark Omni control Audio Rear Internal

For Internal Mode connect your output in (Output 1) RCA  connectors (L+R) for Master Output.
Connect your headphones in front ( ¼ TSR stereo connector).

EXTERNAL MODE (Deck A + Deck B connected to external mixer)

DJ ProMixer Numark Omni Control ASIO External

DJ ProMixer Numark Omni Control Audio Rear External

For External Mode connect your outputs 1.- RCA  connectors (L+R) for Deck A (Output 1), and  2.- RCA connectors (L+R) for Deck B (Output 2).

MIDI SET UP

DJ ProMixer Numark Omni Control MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark OMNI CONTROL MIDI0) and select on the right side NUMARK OMNI CONTROL.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

TWO MIDI MAPS

Overview

DJ ProMixer Numark Omni control MIDI map

(Click to enlarge)

Detail

 DJ ProMixer Numark Omni control MIDI map detail

1.-   PLAY
2.-   PAUSE
3.-   CUE
4.-   PITCH
5.-   SYNC
6.-   KEYLOCK
7.-   PFL
8.-   MANUAL LOOP (1.- IN  2.- OUT / EXIT / RELOOP)
9.-   PITCH BEND
10.- CHANGE FOCUS TREE / TRACKLIST
11.- SCROLL / LOAD / ENTER
12.- LOAD TRACK
13.- FX DRY / WET
14.- FX PARAMETER
15.- MID MAP 1 AND MIDI MAP 2 – FX – ECHO
16.- MIDI MAP 1 FX – FLANGER / MIDI MAP 2 – SCRATCH
17.- MIDI MAP 1 SAMPLER 1 / MIDI MAP 2 – FX FLANGER
18.- MIDI MAP 1 SAMPLER 2 / MIDI MAP 2 – FX WAH
19.- FX ECHO BEAT SYNC
20.- SAMPLER VOLUMEN
21.- PFL VOLUMEN (A AND B)
22.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS) / KILL = PUSH (HI, MID, BASS)
23.- VOLUMEN CONTROLS AND CROSSFADER
24.- WHEELS

info mapping                    info PDF

Citronic MP-X10

HOW TO SET UP?

The system must recognize your Citronic MPCD-X3 as Audio and MIDI device before configuring in DJ ProMixer.

AUDIO AND MIDI SETTINGS

——————————————————————————————————————– IMPORTANT: Install the drivers provided for the manufacturer and check this configuration to install your device
——————————————————————————————————————–

MIDI MAP
Overview

DJ ProMixer Citronic-mp-x10 map

Detail

DJ ProMixer Citronic-mp-x10 map detail

1.-     PLAY / PAUSE
2.-     CUE
3.-     AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) IN  EXIT / RELOOP IN
4.-    TRACK SCROLL / PUSH (LOAD)
5.-    FOLDER SCROLL / PUSH (OPEN-CLOSE)
6.-    CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
7.-    MEMORIZE CUE / LOOP POINT
8.-    DELETE CUE /LOOP POINT
9.-    ENABLE SAMPLER (HOLD BUTTON) (SAMPLES 1,2,3,4)
10.-  FX ECHO
11.-  FX FLANGER
12.-  FX WAH
13.-  REVERSE
14.-  BRAKE
15.-  WHEEL MODE: FX PARAMETER
16.-  WHEEL MODE: VINYL
17.-  WHEEL MODE: SEARCH
18.-  PFL
19-  CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
20-  KEYLOCK
21-  MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
22-  PITCH
23.- BEND (BUTTONS)
24.- BEND (WHEEL)
25.- SCRATCH
26.- SYNC
27.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
28.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Akiyama Syncron

HOW TO SET UP?

The system must recognize your Akiyama Syncron as Audio and MIDI device before configuring in DJ ProMixer.

Akiyama Syncron only requires download and install Akiyama ASIO Driver, once installed you can configure it in DJ ProMixer.

 AUDIO SET UP

Akiyama Syncron has two different configurations (for Internal or External Mode):

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Akiyama Syncron as Audio Sound Card.

AUDIO SETTINGS

INTERNAL MODE (Master + Headphones)

DJ ProMixer Akiyama Syncron ASIO

DJ ProMixer Akiyama Syncron Rear internal

 

 

For Internal Mode choose your output: 1.- for XLR connectors (balanced)  or 2.- for RCA (unbalanced) (1+2).

 

EXTERNAL MODE (Deck A + Deck B connected to external mixer)

DJ ProMixer Akiyama Syncron ASIO external

DJ ProMixer Akiyama Syncron Rear external

For External Mode connect your outputs 1.- RCA  connectors (L+R) for Deck A, and  2.- RCA connectors (L+R) for Deck B.

MIDI SET UP

 DJ ProMixer Akiyama Syncron MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (SYNCRON0) and select on the right side AKIYAMA SYNCRON.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Akiyama Syncron map

 

Detail

 DJ ProMixer Akiyama Syncron map detail


1.-     PLAY / PAUSE
2.-     CUE
3.-     AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) IN  EXIT / RELOOP IN
4.-    TRACK SCROLL / PUSH (LOAD)
5.-    FOLDER SCROLL / PUSH (OPEN-CLOSE)
6.-    CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
7.-    MEMORIZE CUE / LOOP POINT
8.-    DELETE CUE /LOOP POINT
9.-    ENABLE SAMPLER (HOLD BUTTON) (SAMPLES 1,2,3,4)
10.-  FX ECHO
11.-  FX FLANGER
12.-  FX WAH
13.-  REVERSE
14.-  BRAKE
15.-  WHEEL MODE: FX PARAMETER
16.-  WHEEL MODE: VINYL
17.-  WHEEL MODE: SEARCH
18.-  PFL
19-  CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
20-  KEYLOCK
21-  MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
22-  PITCH
23.- BEND (BUTTONS)
24.- BEND (WHEEL)
25.- SCRATCH
26.- SYNC
27.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
28.- DECK´S VOLUMEN CONTROLS AND CROSSFADER

info mapping                    info PDF

Numark Mixtrack Quad

HOW TO SET UP?

The system must recognize your Numark Mixtrack Quad as Audio and MIDI device before configuring in DJ ProMixer.

AUDIO SETTINGS

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Mixtrack Quad as Audio Sound Card.
Note: You do not need install additionals audio drivers, once connected is just plug and play.

DJ ProMixer Audio Mixtrack Pro II

Connect your output in (1) RCA  connectors (L+R) for Master Output.

Connect your headphones in front ( ¼ TSR stereo connector).

Important: Numark Mixtrack Quad is designed to be used as internal mode (with internal Sound Card using master output  & headphones) or external mode (using the internal soundcard for each deck).

MIDI SET UP

DJ ProMixer MIDI Mixtrack 2

 

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MixTrack Quad) and select on the right side NUMARK MIXTRACK QUAD.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview
DJ ProMixer Mixtrack Quad map
(Click to enlarge)

Detail

DJ ProMixer Mixtrack Quad map detail

 

1.-   PLAY / PAUSE
2.-   CUE
3.-   SYNC
4.-   CHANGE FOCUS THREE / TRACKLIST (SHIFT SELECTOR)
5.-   SHIFT + PAD 5 = LOOP SELECTION (AUTO AND MANUAL)
6.-   SHIFT + PAD 6 = SAMPLES SELECTION (1,2,3,4)
7.-   SHIFT + PAD 7 = CUE / LOOP MEMORY SELECTION (1,2,3,4)
8.-   BEND (BUTTONS)
9.-   FX DRY / WET
10.- FX PARAMETER
11.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
12.- SAMPLER VOLUMEN
13.- FX 1, FX 2, FX 3
14.- AUTO LOOP X2
15.- LOAD DECK
16.- CROSSFADER
17.- PFL
18.-TRACKLIST SCROLL
19.- ROTARY KNOBS OF THE MIXER (HI, MID,BASS)
20.- DECK´S VOLUMEN CONTROLS
21.- BEND (WHEEL)
22.- SCRATCH
23.- ENABLE WHEEL VINYL MODE
24.- PITCH

25.- HEADPHONES VOLUMEN (A AND B)

info mapping                    info PDF

Numark Mixtrack / Pro II

HOW TO SET UP?

The system must recognize your Numark Mixtrack / Pro II as Audio Device (only Mixtrack Pro II) and MIDI Device (for booth models) before configuring in DJ ProMixer.

AUDIO SETTINGS

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Mixtrack Pro II as Audio Sound Card.
Note: You do not need install additionals audio drivers, once connected is just plug and play.

 DJ ProMixer Audio Mixtrack Pro II

Connect your output in (1) RCA  connectors (L+R) for Master Output.

Connect your headphones in front ( ¼ TSR stereo connector).

Important: Numark Mixtrack Pro is designed to be used as internal mode (with internal Sound Card using master output  & headphones) or external mode (using the internal soundcard for each deck).

Numark Mixtrack II have not soundcard, it´s only MIDI Controller.

MIDI SET UP

DJ ProMixer MIDI Mixtrack 2

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MixTrack / Pro II) and select on the right side NUMARK MIXTRACK PRO II.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview
Mixtrack Pro II Map_2
(Click to enlarge)

Detail

DJ ProMixer Mixtrack Pro II Map detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   SYNC
4.-   SHIFT SELECTOR
5.-   SHIFT + PAD 5 = LOOP SELECTION (AUTO AND MANUAL)
6.-   SHIFT + PAD 6 = SAMPLES SELECTION (1,2,3,4)
7.-   SHIFT + PAD 7 = CUE / LOOP MEMORY SELECTION (1,2,3,4)
8.-   BEND (BUTTONS)
9.-   FX DRY / WET
10.- FX PARAMETER
11.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
12.- SAMPLER VOLUMEN
13.- FX 1, FX 2, FX 3
14.- AUTO LOOP X2
15.- LOAD DECK
16.- CHANGE FOCUS TREE / TRACKLIST
17.- PFL
18.-TRACKLIST SCROLL
19.- ROTARY KNOBS OF THE MIXER (HI, MID,BASS)
20.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
21.- BEND (WHEEL)
22.- SCRATCH
23.- ENABLE WHEEL VINYL MODE
24.- PITCH

25.- HEADPHONES VOLUMEN (A AND B)

info mapping                    info PDF

Denon DN MC 6000 MKII

HOW TO SET UP?

The system must recognize your Denon DN-MC 6000 MKII as Audio and MIDI device before configuring in DJ ProMixer.

Denon DN-MC 6000 MKII only requires download and install Denon DJ Asio Driver, once installed you can configure it in DJ ProMixer.

DJ ProMixer Driver ASIO Denon DJ

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your DN-MC6000 MKII as Audio Sound Card.

CONFIGURE YOUR AUDIO SETTINGS

DJ ProMixer Denon MC-6000 MKII ASIO

DJ ProMixer Denon MC6000MK2 Audio Outputs

For Internal Mode choose your output (1.- for XLR connectors or 2.- for RCA). Additional output 3.- Booth / Send Out
Important: DN-MC6000 MKII is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI CONFIGURATION

DJ ProMixer Denon MIDI  MC - 6000 MKII

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DN-MC6000 MKII) and select on the right side DENON MC6000MKII.XML.  MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

DJ ProMixer Denon MC6000 MKII Map(Click to enlarge)

                                                                  Detail

DJ ProMixer Denon MC6000 MKII Map Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   MANUAL LOOP (1.- IN  2.- OUT – EXIT – RELOOP)
4.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) IN / EXIT / RELOOP MOVE WITH “-“ 1/2 AND “+” x2
5.-   SELECTOR CUE / LOOP – SAMPLES
6.-   KEYLOCK
7.-   EFFECTS DIRECT BUTTONS FX 1, FX 2, FX3
8.-   CUE / LOOP MEMORY (4 DIRECT BUTTONS) (SELECTOR 5 OFF)
8.-  SAMPLER DIRECT BUTTONS (1, 2, 3, 4) (SELECTOR 5 ON)
9.-   MEMORY CUE / LOOP (SHIFT BUTTON)
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL / CHANGE FOCUS
15.- LOAD DECK
16.- CHANNEL SELECTOR
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE
26.- CHANGE FOCUS TREE / PLAYLIST

info mapping                    info PDF

Denon DN MC 2000

HOW TO SET UP?

The system must recognize your Denon DN-MC2000 as Audio and MIDI device before configuring in DJ ProMixer.

Denon DN-MC 2000 only requires download and install Denon DJ Asio Driver, once installed you can configure it in DJ ProMixer.

DJ ProMixer MC 2000 Denon Asio Driver

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Denon DN-MC 2000 as Audio Sound Card.

AUDIO SET UP

DJ ProMixer Denon MC-2000 ASIO

Important: DN-MC 2000 is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

 DJ ProMixer Denon MC-2000 MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DN-MC3000) and select on the right side DENON MC3000.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Denon MC2000 Map

Detail

DJ ProMixer MC2000 Map Detail

1.-  PLAY / PAUSE
2.-  CUE
3.-  MANUAL LOOP (1.- IN  2.- OUT – EXIT – RELOOP)
4.-  AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) IN  EXIT / RELOOP MOVE WITH “-“ 1/2 AND “+” x2
5.-  SELECTOR CUE (1,2,3,4) / SAMPLES (1,2,3,4)
6.-  KEYLOCK
7.-  EFFECTS DIRECT BUTTONS FX 1, FX 2, FX3
8.-  CUE / LOOP MEMORY (4 DIRECT BUTTONS) (SELECTOR OFF)
9.-  SAMPLES (4 DIRECT BUTTONS) (SELECTOR ON)
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK
16.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
17.- PFL
18.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
19.- SAMPLER VOLUMEN
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- TRACKLIST SELECTOR (PLAYLIST, GROUPS, EXPLORER)
26.- MEMORY CUE / LOOP DECK A
27.- MEMORY CUE / LOOP DECK B
28.- CHANGE FOCUS TREE
29.- CHANGE FOCUS TRACKS

info mapping                    info PDF

Numark Mixdeck

HOW TO SET UP?

The system must recognize your Numark Mixdeck as Audio and MIDI Device before configuring in DJ ProMixer.
Numark Mixdeck only requires download and install Numark Asio Driver.

DJ Promixer Driver Audio Numark Mixdeck

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Numark Mixdeck as Audio Sound Card.

AUDIO SETTINGS

DJ ProMixer Numark Mixdeck Audio Set Up

DJ ProMixer Numark Mixdeck front

For Internal Mode choose your output: 1.- for XLR connectors (balanced)  or 2.- for RCA (unbalanced).

Important: Numark Mixdeck is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

DJ ProMixer Numark Mixdeck MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark Mixdeck) and select on the right side NUMARK MIXDECK.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

DJ ProMixer Numark Mixdeck map

Detail

DJ ProMixer Numark Mixdeck map detail

1.- PLAY
2.- PAUSE

3.- CUE

4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
 
5.- SCROLL / LOAD / ENTER

6.- CHANGE FOCUS TREE / TRACKLIST
7.- REVERSE / BRAKE

8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP) DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)

10.- SEARCH (WHEEL MODE) 
11.- CUE / LOOP MEMORY (1, 2, 3) (NORMAL MODE) / SAMPLES (1, 2, 3 WITH SAMPLER BUTTON ACTIVATED)
12.- SAMPLER MODE ON / OFF
13.- MEMORIZE CUE / LOOP
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- FX 1 (ECHO) LEFT (ON) CENTER (OFF) – FX 2 (FLANGER) RIGHT (ON) CENTER (OFF)
19.- FX 3 (WAH)

20.- FX DRY / WET
21.- FX PARAMETER
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- DECK VOLUMEN
25.- HEADPHONES VOLUMEN
26.- DECK SELECTOR (DECK A / DECK B) (ONLY DUAL MODE)
27.-
LINK TO PC (SOURCE)

info mapping                    info PDF

Numark NDX 900

HOW TO SET UP?

The system must recognize your Numark NDX-900 device/s before configuring in DJ ProMixer.
IMPORTANT: Numark NDX-900 is a MIDI and audio sound card device

MIDI CONFIGURATION

Single Mode (2 Numark NDX-900 Connected)

DJ ProMixer MIDI NDX 900 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark NDX900 0) and select on the right side NUMARK NDX-900(SINGLE A).XML. Select in MIDI PORT / MIDI MAP 2 on the left side the other device (Numark NDX900 I) and select on the right side NUMARK NDX-900(SINGLE B).XML

Dual Mode

DJ ProMixer MIDI NDX 900 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side Numark NDX900 0, and select on the right side NUMARK NDX-900 (A AND B).XML. Nothing selected in MIDI PORT / MIDI MAP 2 How to change the decks? Two ways: 1.- Hardware: Use the “Eject Button”. 2.- Software: By clicking the headphone button of the deck.

Load button

AUDIO CONFIGURATION

Open DJ ProMixer and go to “Config”, open “Audio Setup”, here you can select your Numark NDX-900 as Audio Sound Card.

DJ ProMixer MIDI CD Audio

MIDI MAP

DJ ProMixer Numark NDX 900 Map

1.- PLAY
2.- PAUSE

3.- CUE

4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
 
5.- SCROLL / LOAD / ENTER

6.- CHANGE FOCUS TREE / TRACKLIST
7.- REVERSE / BRAKE

8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP) DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)

10.- SEARCH (WHEEL MODE) 
11.- CUE / LOOP MEMORY (1, 2, 3) (NORMAL MODE) / SAMPLES (1, 2, 3 WITH SAMPLER BUTTON ACTIVATED)
12.- SAMPLER MODE ON / OFF
13.- MEMORIZE CUE / LOOP
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- FX 1 (ECHO) LEFT (ON) CENTER (OFF) – FX 2 (FLANGER) RIGHT (ON) CENTER (OFF)
19.- FX 3 (WAH)

20.- FX DRY / WET
21.- FX PARAMETER
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- DECK VOLUMEN
25.- HEADPHONES VOLUMEN
26.- DECK SELECTOR (DECK A / DECK B) (ONLY DUAL MODE)
27.-
LINK TO PC (SOURCE)

info mapping                    info PDF

MIDI CD Controllers (single or dual mode) -no audio sound card-

HOW TO SET UP?
The system must recognize your MIDI CD controller/s before configuring in DJ ProMixer.

IMPORTANT:
– Check and install the drivers of your device from the oficial website.

Plug your MIDI CD Controller and go to “Config” to configurate it.

MIDI CONFIGURATION

Single Mode (2 MIDI CD Controllers connected) DJ ProMixer MIDI NDX 800 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one MIDI CD Controller device and select on the right side the SINGLE A.XML map. Select in MIDI PORT / MIDI MAP 2 on the left side the other MIDI CD Controller device and select on the right side the SINGLE B.XML map

Dual Mode MIDI NDX 800 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side your MIDI CD Controller device, and select on the right side the (A AND B).XML map. Nothing selected in MIDI PORT / MIDI MAP 2

How to change the decks? Two ways: 1.- Hardware: Check the assigned button at MIDI map. 2.- Software: By clicking the headphone button of the deck.

MIDI CD Controllers (single or dual mode) -with audio sound card-

HOW TO SET UP?
The system must recognize your MIDI CD controller/s before configuring in DJ ProMixer.

IMPORTANT:
– Check and install the drivers of your device from the oficial website.

Plug your MIDI CD Controller and go to “Config” to configurate it.

MIDI CONFIGURATION

Single Mode (2 MIDI CD Controllers connected) DJ ProMixer MIDI NDX 800 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one MIDI CD Controller device and select on the right side the SINGLE A.XML map. Select in MIDI PORT / MIDI MAP 2 on the left side the other MIDI CD Controller device and select on the right side the SINGLE B.XML map

Dual Mode MIDI NDX 800 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side your MIDI CD Controller device, and select on the right side the (A AND B).XML map. Nothing selected in MIDI PORT / MIDI MAP 2

How to change the decks? Two ways: 1.- Hardware: Check the assigned button at MIDI map. 2.- Software: By clicking the headphone button of the deck.

AUDIO CONFIGURATION

Open DJ ProMixer and go to “Config” open “Audio Setup”, here you can select your MIDI CD Controller as Audio Sound Card.
There are two ways to connect your device/s as Audio Sound Card (It depends of the drivers of the manufacturer):

1.- ASIO Driver Mode (If it is supported)

DJ ProMixer MIDI CD ASIO

 

2.- Direct sound

DJ ProMixer MIDI CD Audio

MIDI CD Controllers (single or dual mode) -Generic configuration-

HOW TO SET UP?

The system must recognize your MIDI CD controller/s before configuring in DJ ProMixer.

IMPORTANT:
– Check and install the drivers of your device from the oficial website.
– Your MIDI CD Controller could be only MIDI or MIDI with audio sound card integrated.

Plug your MIDI CD Controller and go to “Config” to configurate it.

MIDI CONFIGURATION

Single Mode (2 MIDI CD Controllers connected) DJ ProMixer MIDI NDX 800 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one MIDI CD Controller device and select on the right side the SINGLE A.XML map. Select in MIDI PORT / MIDI MAP 2 on the left side the other MIDI CD Controller device and select on the right side the SINGLE B.XML map

Dual Mode MIDI NDX 800 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side your MIDI CD Controller device, and select on the right side the (A AND B).XML map. Nothing selected in MIDI PORT / MIDI MAP 2

How to change the decks? Two ways: 1.- Hardware: Check the assigned button at MIDI map. 2.- Software: By clicking the headphone button of the deck.

AUDIO CONFIGURATION
(If your MIDI CD Controller has audio sound card)

Open DJ ProMixer and go to “Config” open “Audio Setup”, here you can select your MIDI CD Controller as Audio Sound Card.
There are two ways to connect your device/s as Audio Sound Card (It depends of the drivers of the manufacturer):

1.- ASIO Driver Mode (If it is supported)

DJ ProMixer MIDI CD ASIO

 

2.- Direct sound

DJ ProMixer MIDI CD Audio

DUAL MODE:

Normally every device has assigned a physical button to change the deck.
You can change also with headphones button (A / B) or / and and A / B button of the track info.

SPECIFIC CONFIGURATIONS:

MIDI CD Controllers (single or dual mode) -no audio sound card-
MIDI CD Controllers (single or dual mode) -with audio sound card-

Pioneer CDJ / XDJ (Audio and HID Advanced Configuration)

HOW TO SET UP CDJ / XDJ?

Your System must recognize your Pioneer CDJ / XDJ as Audio and HID device before configuring in DJ ProMixer.
Download and install Pioneer CDJ ASIO Driver from the oficial website: http://pioneerdj.com/support/

1.- CONNECT YOUR CDJ / XDJ

1. Plug your CDJ / XDJ to your PC (USB) to recognize your device/s as Audio Sound Card and HID Device. Turn on your CDJ / XDJ and press “Link” button, select “Control Mode” and push the rotary button to connect.                                   (Display detail after connect your CDJ )

2. AUDIO SET UP

2. Open DJ ProMixer and go to “Config” open “Audio Setup”, here you can select your CDJ / XDJ as Audio Sound Card. There are two ways to connect your CDJ / XDJ as Audio Sound Card:
2.1 ASIO Driver Mode (recommended):
(Pioneer ASIO Driver required)

DJ ProMixer CDJ ASIO

2.2 Direct Sound:

DJ ProMixer CDJ Direct Sound

(For other configuration choose your Work Mode and Audio Sound Card).

3. HID CONTROL SET UP:

3.1. Single Mode (2 CDJ / XDJ Connected)

DJ ProMixer CDJ Single

Select in HID PORT / MIDI MAP 1 on the left side one device (PIONEER CDJ / XDJ (your model) HID0 and select on the right side PIONEER CDJ / XDJ-(your model)SINGLEA.XML. Select in HID PORT / MIDI MAP 2 on the left side the other device (PIONEER CDJ / XDJ- (your model) HID 1 and select on the right side PIONEER CDJ / XDJ-(your model)SINGLEB.XML

IMPORTANT: Normally you don´t know what´s the first device recognized, it depends of the system, then if your devices are inverted, you must to swap it on the left side of the HID PORT.

3.2. Dual Mode:

DJ ProMixer CDJ Dual

Select in HID PORT / MIDI MAP 1 on the left side your PIONEER CDJ / XDJ-(your model) HID and select on the right side PIONEER CDJ / XDJ-(your model).XML. Nothing selected in HID PORT / HID MAP 2 How to change the decks? By default your CDJ / XDJ start in “A” Deck to change to “B” in Dual mode you have two ways: 1- Hardware: By pressing “Back” button. 2. Software: By clicking the headphone button of the selected deck.

Audiophony DJam Ultimate

HOW TO SET UP?

The system must to recognize your Audiophony DJam Ultimate as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO AND MIDI SETTINGS

——————————————————————————————————————– IMPORTANT: Install the drivers provided for the manufacturer and check the configuration of this equivalent controller.
——————————————————————————————————————–

MIDI MAP (Overview)

Audiophony DJam Ultimate MIDI MAP

(Click to enlarge)

Detail

Audiophony DJam Ultimate MIDI MAP Detail 

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF

Stanton DJC. 4

HOW TO SET UP? 

The system must to recognize your Stanton DJC. 4 Pro as Audio Device and MIDI Device before configure in DJ ProMixer.

CONFIGURE YOUR AUDIO AND MIDI SETTINGS

—————————————————————————————————————
IMPORTANT: Install the drivers provided for the manufacturer and check the configuration of this equivalent controller.
—————————————————————————————————————

MIDI MAP
(Overview)

Stanton DJC4 MIDI MAP
(Click to enlarge)

Detail

Stanton DJC4 MIDI MAP Detail

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK 
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF