MIDI CD Controllers (single or dual mode) -Generic configuration-

HOW TO SET UP?

The system must recognize your MIDI CD controller/s before configuring in DJ ProMixer.

IMPORTANT:
– Check and install the drivers of your device from the oficial website.
– Your MIDI CD Controller could be only MIDI or MIDI with audio sound card integrated.

Plug your MIDI CD Controller and go to “Config” to configurate it.

MIDI CONFIGURATION

Single Mode (2 MIDI CD Controllers connected) DJ ProMixer MIDI NDX 800 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one MIDI CD Controller device and select on the right side the SINGLE A.XML map. Select in MIDI PORT / MIDI MAP 2 on the left side the other MIDI CD Controller device and select on the right side the SINGLE B.XML map

Dual Mode MIDI NDX 800 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side your MIDI CD Controller device, and select on the right side the (A AND B).XML map. Nothing selected in MIDI PORT / MIDI MAP 2

How to change the decks? Two ways: 1.- Hardware: Check the assigned button at MIDI map. 2.- Software: By clicking the headphone button of the deck.

AUDIO CONFIGURATION
(If your MIDI CD Controller has audio sound card)

Open DJ ProMixer and go to “Config” open “Audio Setup”, here you can select your MIDI CD Controller as Audio Sound Card.
There are two ways to connect your device/s as Audio Sound Card (It depends of the drivers of the manufacturer):

1.- ASIO Driver Mode (If it is supported)

DJ ProMixer MIDI CD ASIO

 

2.- Direct sound

DJ ProMixer MIDI CD Audio

DUAL MODE:

Normally every device has assigned a physical button to change the deck.
You can change also with headphones button (A / B) or / and and A / B button of the track info.

SPECIFIC CONFIGURATIONS:

MIDI CD Controllers (single or dual mode) -no audio sound card-
MIDI CD Controllers (single or dual mode) -with audio sound card-

Posted in Compatible Hardware | Tagged , , , , , , | Leave a comment

Pioneer CDJ – 2000 Nexus

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 2000 NEXUS MAP

DJ ProMixer CDJ2000Nexus Map

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
6.-   DIRECT AUTO LOOP (STARTS IN 4 BEATS)
7.-   CUE / SAMPLES / EFFECTS / LOOPS DIRECT BUTTONS
8.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
9.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- DELETE CUE / LOOP POINT
11.- MEMORIZE CUE / LOOP POINT
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- KEYLOCK
16.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
17.- PITCH
18.- BEND
19.- SCRATCH (WHEEL)
20.- SYNC
21.- FX DRY / WET
22.- FX PARAMETER
23.- CHANGE DECK (ONLY IN DUAL MODE)
24.- NEEDLE SEARCH
25.-
LINK TO PC

IMPORTANT: TO CONNECT 2 PIONEER CDJ-2000 NEXUS YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Pioneer CDJ – 2000

HOW TO SET UP?

– Single or dual mode (two or one CDJ)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 2000 MAP

DJ ProMixer Pioneer CDJ2000map

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
6.-   DIRECT AUTO LOOP (STARTS IN 4 BEATS)
7.-   CUE / SAMPLES / EFFECTS / LOOPS DIRECT BUTTONS
8.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
9.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- DELETE CUE / LOOP POINT
11.- MEMORIZE CUE / LOOP POINT
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- KEYLOCK
16.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
17.- PITCH
18.- BEND
19.- SCRATCH (WHEEL)
20.- SYNC
21.- FX DRY / WET
22.- FX PARAMETER
23.- CHANGE DECK (ONLY IN DUAL MODE)
24.- L
INK TO PC

IMPORTANT: TO CONNECT 2 PIONEER CDJ-2000 YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Pioneer CDJ – 900 Nexus

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 900 NEXUS MAP

DJ ProMixer CDJ900Nexus

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
6.-   DIRECT AUTO LOOP (STARTS IN 4 BEATS)
7.-   CUE / SAMPLES / EFFECTS / LOOPS DIRECT BUTTONS
8.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
9.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- DELETE CUE / LOOP POINT
11.- MEMORIZE CUE / LOOP POINT
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- KEYLOCK
16.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
17.- PITCH
18.- BEND
19.- SCRATCH (WHEEL)
20.- SYNC
21.- FX DRY / WET
22.- CHANGE DECK (ONLY IN DUAL MODE)
23.- LINK TO PC

IMPORTANT: TO CONNECT 2 PIONEER CDJ-900 NEXUS YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Pioneer CDJ 900

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 900

DJ ProMixer CDJ900

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
6.-   SYNC
7.-   CUE / SAMPLES / EFFECTS / LOOPS DIRECT BUTTONS
8.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
9.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- DELETE CUE / LOOP POINT
11.- MEMORIZE CUE / LOOP POINT
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- KEYLOCK
16.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
17.- PITCH
18.- BEND
19.- SCRATCH (WHEEL)
20.- FX DRY / WET
21.- CHANGE DECK (ONLY IN DUAL MODE)
22.- LINK TO PC

IMPORTANT: TO CONNECT 2 PIONEER CDJ-900 YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Pioneer CDJ – 850

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 850

DJ ProMixer Pioneer CDJ850

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
6.-   SYNC
7.-   CUE / SAMPLES / EFFECTS / LOOPS DIRECT BUTTONS
8.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
9.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- DELETE CUE / LOOP POINT
11.- MEMORIZE CUE / LOOP POINT
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- KEYLOCK
16.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
17.- PITCH
18.- BEND
19.- SCRATCH (WHEEL)
20.- FX DRY / WET
21.- CHANGE DECK (ONLY IN DUAL MODE)
22.- LINK TO PC

IMPORTANT: TO CONNECT 2 PIONEER CDJ-850 YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Pioneer XDJ – 1000

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER XDJ – 1000

DJ ProMixer Pioneer XDJ-1000

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   REVERSE
5.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
6.-   SYNC
7.-   CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
8.-   KEYLOCK
9.-   PITCH
10.- SCRATCH (WHEEL)
11.- BEND
12.- SCROLL / LOAD / ENTER
13.- CHANGE FOCUS TREE / TRACKLIST
14.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
15.- FX DRY / WET
16.- CHANGE DECK (ONLY IN DUAL MODE)
17.- LINK TO PC

IMPORTANT: TO CONNECT 2 PIONEER XDJ-1000 YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , , | Leave a comment

Pioneer CDJ / XDJ (Audio and HID Advanced Configuration)

HOW TO SET UP CDJ / XDJ?

Your System must recognize your Pioneer CDJ / XDJ as Audio and HID device before configuring in DJ ProMixer.
Download and install Pioneer CDJ ASIO Driver from the oficial website: http://pioneerdj.com/support/

1.- CONNECT YOUR CDJ / XDJ

1. Plug your CDJ / XDJ to your PC (USB) to recognize your device/s as Audio Sound Card and HID Device. Turn on your CDJ / XDJ and press “Link” button, select “Control Mode” and push the rotary button to connect.                                   (Display detail after connect your CDJ )

2. AUDIO SET UP

2. Open DJ ProMixer and go to “Config” open “Audio Setup”, here you can select your CDJ / XDJ as Audio Sound Card. There are two ways to connect your CDJ / XDJ as Audio Sound Card:
2.1 ASIO Driver Mode (recommended):
(Pioneer ASIO Driver required)

DJ ProMixer CDJ ASIO

2.2 Direct Sound:

DJ ProMixer CDJ Direct Sound

(For other configuration choose your Work Mode and Audio Sound Card).

3. HID CONTROL SET UP:

3.1. Single Mode (2 CDJ / XDJ Connected)

DJ ProMixer CDJ Single

Select in HID PORT / MIDI MAP 1 on the left side one device (PIONEER CDJ / XDJ (your model) HID0 and select on the right side PIONEER CDJ / XDJ-(your model)SINGLEA.XML. Select in HID PORT / MIDI MAP 2 on the left side the other device (PIONEER CDJ / XDJ- (your model) HID 1 and select on the right side PIONEER CDJ / XDJ-(your model)SINGLEB.XML

IMPORTANT: Normally you don´t know what´s the first device recognized, it depends of the system, then if your devices are inverted, you must to swap it on the left side of the HID PORT.

3.2. Dual Mode:

DJ ProMixer CDJ Dual

Select in HID PORT / MIDI MAP 1 on the left side your PIONEER CDJ / XDJ-(your model) HID and select on the right side PIONEER CDJ / XDJ-(your model).XML. Nothing selected in HID PORT / HID MAP 2 How to change the decks? By default your CDJ / XDJ start in “A” Deck to change to “B” in Dual mode you have two ways: 1- Hardware: By pressing “Back” button. 2. Software: By clicking the headphone button of the selected deck.

Posted in Compatible Hardware | Tagged , , , , , , , , | Leave a comment

Numark NDX 800

HOW TO SET UP?

The system must recognize your Numark NDX-800 device/s before configuring in DJ ProMixer.
IMPORTANT: Numark NDX-800 is a MIDI Device (It has not integrated audio device/s) For audio configuration choose your work mode and audio sound card/s).

MIDI CONFIGURATION

Single Mode (2 Numark NDX-800 Connected) DJ ProMixer MIDI NDX 800 Single

Select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark NDX800 0) and select on the right side NUMARK NDX-800(SINGLE A).XML. Select in MIDI PORT / MIDI MAP 2 on the left side the other device (Numark NDX800 I) and select on the right side NUMARK NDX-800(SINGLE B).XML

Dual Mode MIDI NDX 800 Dual

Select in MIDI PORT / MIDI MAP 1 on the left side Numark NDX800 0, and select on the right side NUMARK NDX-800 (A AND B).XML. Nothing selected in MIDI PORT / MIDI MAP 2 How to change the decks? Two ways: 1.- Hardware: Use the “Eject Button”. 2.- Software: By clicking the headphone button of the deck.

Load button

MIDI MAP

  DJ ProMixer Numark NDX 800 Map1.- PLAY
2.- PAUSE

3.- CUE

4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
 
5.- SCROLL / LOAD / ENTER

6.- CHANGE FOCUS TREE / TRACKLIST
7.- REVERSE / BRAKE

8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP) DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)

10.- SEARCH (WHEEL MODE) 
11.- CUE / LOOP MEMORY (1, 2, 3) (NORMAL MODE) / SAMPLES (1, 2, 3 WITH SAMPLER BUTTON ACTIVATED)
12.- SAMPLER MODE ON / OFF
13.- MEMORIZE CUE / LOOP
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- FX 1 (ECHO) LEFT (ON) CENTER (OFF) – FX 2 (FLANGER) RIGHT (ON) CENTER (OFF)
19.- FX 3 (WAH)

20.- FX DRY / WET
21.- FX PARAMETER
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- DECK VOLUMEN
25.- HEADPHONES VOLUMEN
26.- DECK SELECTOR (DECK A / DECK B) (ONLY DUAL MODE)
27.-
LINK TO PC (SOURCE)

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Pioneer DDJ WeGO

HOW TO SET UP?

The system must recognize your Pioneer DDJ WeGO as Audio and MIDI device before configuring in DJ ProMixer.

Pioneer DDJ WeGo only requires download and install the latest drivers, once installed you can configure in DJ ProMixer.

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Pioneer WeGO as Audio Sound Card.

AUDIO SET UP

DJ ProMixer ASIO Pioneer DDJ

Important: Pioneer DDJ-WeGO is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

 In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (Pioneer DDJ-WeeGo) and select on the right side PIONEER DDJ WEEGO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

DJ ProMixer MIDI WeeGo


MIDI MAP (Overview)

DJ ProMixer Pioneer DDJ - Weego Map

(Click to enlarge)

Detail

DJ ProMixer Pioneer DDJ - Weego Map Detail

1.- PLAY/ PAUSE
2.- CUE
3.- MANUAL LOOP (IN)
4.- MANUAL LOOP (OUT – EXIT – RELOOP)
5.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
6.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 2 BEATS)
7.- MEMORY CUE / LOOP (1,2,3,4)
8.- ENABLE SAMPLER (1,2,3,4) 
9.- PITCH
10.- SYNC
11.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
12.- ROTARY KNOBS OF THE MIXER  (HI, MID, BASS)
13.- TRACKLIST SCROLL, + SHIFT : BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
14.- LOAD DECK (A AND B)
15.- SHIFT
16.- PFL, +SHIFT: CHANGE WHEEL COLOR
17.- BEND (WHEEL)
18.- SCRATCH

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Numark DJ2Go

HOW TO SET UP?

The system must recognize your Numark DJ2 Go before configuring in DJ ProMixer.

IMPORTANT: Numark DJ2 Go is a MIDI Device (It has not integrated audio device/s) For audio configuration choose your work mode and audio sound card/s).

 MIDI SET UP

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (Numark DJ2Go) and select on the right side NUMARK DJ2GO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

DJ ProMixer DJ2Go MIDI

MIDI MAP

(Overview)DJ ProMixer Numark DJ2Go Map

(Detail)
Numark DJ2Go Map detail

1.- PLAY / PAUSE
2.- CUE
3.- PITCH
4.- PITCH BEND
5.- SYNC
6.- PFL
7.- DECK VOLUMEN
8.- WHEEL
9.- CROSSFADER
10.- LOAD
11.- SCROLL
12.- CHANGE FOCUS TREE / TRACKLIST
13.- OPEN-CLOSE / LOAD
14.- HEADPHONES VOLUMEN

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Citronic MPCD-X3

HOW TO SET UP?

The system must recognize your Citronic MPCD-X3 as MIDI Device before configuring in DJ ProMixer.

MIDI SETTINGS

——————————————————————————————————————– IMPORTANT: Install the drivers provided for the manufacturer and check this configuration to install your device
——————————————————————————————————————–

MIDI MAP

 Citronic MPCD-X3 Map

 

  1.- PLAY / PAUSE
  2.- CUE
  3.- CUP (CUE & PLAY)
  4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
  5.- TRACK SCROLL / PUSH (LOAD)
  6.- FOLDER SCROLL / PUSH (OPEN-CLOSE)
  7.- REVERSE
  8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP)
DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

  9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- SELECTOR AUTOLOOP (FROM ¼ TO 32 BEATS) / FX ECHO BEAT SYNC (FROM 1/8 TO 2/1) 
11.- SELECTOR AUTOLOOP / FX BEAT << MOVE DOWN / MOVE UP>>
12.- WHEEL MODE (SCRATCH, SEARCH, FX)
13.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- MEMORIZE CUE / LOOP POINT
19.- DELETE CUE /LOOP POINT

20.- SAMPLE MODE ACTIVATED
21.- CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- EFFECTS (ECHO, FLANGER, WAH)
25.- DECK SELECTOR (DECK A / DECK B)
26.-
LINK TO PC

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Stanton CMP.800

HOW TO SET UP?

The system must recognize your Stanton CMP.800 as MIDI Device before configuring in DJ ProMixer.

MIDI SETTINGS

——————————————————————————————————————-
IMPORTANT: Install the drivers provided for the manufacturer and check this configuration to install your device
——————————————————————————————————————–

MIDI MAP

 Stanton CMP 800 Map

 

  1.- PLAY / PAUSE
  2.- CUE
  3.- CUP (CUE & PLAY)
  4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
  5.- TRACK SCROLL / PUSH (LOAD)
  6.- FOLDER SCROLL / PUSH (OPEN-CLOSE)
  7.- REVERSE
  8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP)
DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

  9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- SELECTOR AUTOLOOP (FROM ¼ TO 32 BEATS) / FX ECHO BEAT SYNC (FROM 1/8 TO 2/1) 
11.- SELECTOR AUTOLOOP / FX BEAT << MOVE DOWN / MOVE UP>>
12.- WHEEL MODE (SCRATCH, SEARCH, FX)
13.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
14.- KEYLOCK (BY DEFAULT DISABLED)
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- MEMORIZE CUE / LOOP POINT
19.- DELETE CUE /LOOP POINT

20.- SAMPLE MODE ACTIVATED
21.- CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- EFFECTS (ECHO, FLANGER, WAH)
25.- DECK SELECTOR (DECK A / DECK B)
26.-
LINK TO PC

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Audiophony CDX6

HOW TO SET UP?
The system must recognize your Audiophony CDX6 as MIDI Device before configuring in DJ ProMixer.

MIDI SETTINGS

——————————————————————————————————————– IMPORTANT: Install the drivers provided for the manufacturer and check this configuration to install your device
——————————————————————————————————————–

MIDI MAP

 Audiophony CDX6 Map

  1.- PLAY / PAUSE
  2.- CUE
  3.- CUP (CUE & PLAY)
  4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
  5.- TRACK SCROLL / PUSH (LOAD)
  6.- FOLDER SCROLL / PUSH (OPEN-CLOSE)
  7.- REVERSE
  8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP)
DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

  9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- SELECTOR AUTOLOOP (FROM ¼ TO 32 BEATS) / FX ECHO BEAT SYNC (FROM 1/8 TO 2/1) 
11.- SELECTOR AUTOLOOP / FX BEAT << MOVE DOWN / MOVE UP>>
12.- WHEEL MODE (SCRATCH, SEARCH, FX)
13.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- MEMORIZE CUE / LOOP POINT
19.- DELETE CUE /LOOP POINT

20.- SAMPLE MODE ACTIVATED
21.- CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- EFFECTS (ECHO, FLANGER, WAH)
25.- DECK SELECTOR (DECK A / DECK B)
26.-
LINK TO PC

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Akiyama Kuro / K2

HOW TO SET UP?

The system must recognize your Akiyama Kuro / K2 Device before configuring in DJ ProMixer.

IMPORTANT: Akiyama Kuro / K2 is a MIDI Device (It has not integrated audio device/s) For audio configuration choose your work mode and audio sound card/s).

MIDI CONFIGURATION

Single Mode (2 Akiyama Kuro / K2 Connected)

Akiyama Kuro single mode

Select in MIDI PORT / MIDI MAP 1 on the left side one device (Midi Controller0) and select on the right side AKIYAMA KURO (A OR B).XML. Select in MIDI PORT / MIDI MAP 2 on the left side the other device (Midi Controller1) and select on the right side AKIYAMA KURO (A OR B).XML

Dual Mode

DJ ProMixer Akiyama Kuro Dual Mode

Select in MIDI PORT / MIDI MAP 1 on the left side your Akiyama Kuro / K2 (Midi Controller0) and select on the right side AKIYAMA KURO (A AND B).XML. Nothing selected in MIDI PORT / MIDI MAP 2

How to change the decks? Akiyama Kuro / K2 has two direct buttons to select the deck, also it show at the display as “Player A” or “Player B”, if your devices are inverted (it depens of the system) swap your devices in Config.

Deck selector

MIDI MAP

Akiyama Kuro Map

  1.- PLAY / PAUSE
  2.- CUE
  3.- CUP (CUE & PLAY)
  4.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
  5.- TRACK SCROLL / PUSH (LOAD)
  6.- FOLDER SCROLL / PUSH (OPEN-CLOSE)
  7.- REVERSE
  8.- MANUAL LOOP (IN – OUT – EXIT / RELOOP)
DIRECT AUTO LOOP (IN / EXIT) (STARTS IN 4 BEATS)

  9.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
10.- SELECTOR AUTOLOOP (FROM ¼ TO 32 BEATS) / FX ECHO BEAT SYNC (FROM 1/8 TO 2/1) 
11.- SELECTOR AUTOLOOP / FX BEAT << MOVE DOWN / MOVE UP>>
12.- WHEEL MODE (SCRATCH, SEARCH, FX)
13.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
14.- KEYLOCK
15.- PITCH

16.- PITCH BEND
17.- SYNC
18.- MEMORIZE CUE / LOOP POINT
19.- DELETE CUE /LOOP POINT

20.- SAMPLE MODE ACTIVATED
21.- CUE LOOP MEMORY (1 TO 4) (NORMAL MODE) / SAMPLES (1 TO 4) (SAMPLE BUTTON ACTIVATED)
22.- BEND (WHEEL)
23.- SCRATCH (WHEEL)
24.- EFFECTS (ECHO, FLANGER, WAH)
25.- DECK SELECTOR (DECK A / DECK B)
26.-
LINK TO PC

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Audiophony DJam Ultimate

HOW TO SET UP?

The system must to recognize your Audiophony DJam Ultimate as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO AND MIDI SETTINGS

——————————————————————————————————————– IMPORTANT: Install the drivers provided for the manufacturer and check the configuration of this equivalent controller.
——————————————————————————————————————–

MIDI MAP (Overview)

Audiophony DJam Ultimate MIDI MAP

(Click to enlarge)

Detail

Audiophony DJam Ultimate MIDI MAP Detail 

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Akiyama Tempus

HOW TO SET UP?

The system must to recognize your Akiyama Tempus as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO SETTINGS

Akiyama Tempus only requires download and install Akiyama Asio Driver.

Akiyama ASIO

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Akiyama Tempus as Audio Sound Card.

Akiyama Tempus Audio

Akiyama Tempus Back

For Internal Mode choose your output: 1.- for ¼ TSR connectors (balanced)  or 2.- for RCA (unbalanced).

Important: Akiyama Tempus is designed to be used in internal mode (with internal Sound Card), but you can use also with DJ ProMixer in external mode (with other/s Sound Card/s and external mixer).

MIDI CONFIGURATION

Akiyama Tempus MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (TEMPUS) and select on the right side AKIYAMA TEMPUS.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP (Overview)

(Click to enlarge)

Akiyama Tempus MIDI MAP

Detail

Akiyama Tempus MIDI MAP Detail

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , | Leave a comment

Stanton DJC. 4

HOW TO SET UP? 

The system must to recognize your Stanton DJC. 4 Pro as Audio Device and MIDI Device before configure in DJ ProMixer.

CONFIGURE YOUR AUDIO AND MIDI SETTINGS

—————————————————————————————————————
IMPORTANT: Install the drivers provided for the manufacturer and check the configuration of this equivalent controller.
—————————————————————————————————————

MIDI MAP
(Overview)

Stanton DJC4 MIDI MAP
(Click to enlarge)

Detail

Stanton DJC4 MIDI MAP Detail

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK 
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Audiophony DJazz Pro

HOW TO SET UP?

The system must to recognize your Audiophony DJazz Pro as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO AND MIDI SETTINGS

——————————————————————————————————————–
IMPORTANT: Install the drivers provided for the manufacturer and check the configuration of this equivalent controller.
——————————————————————————————————————–

MIDI MAP
(Overview)

Audiophony DJazz Pro MIDI MAP
(Click to enlarge)

Detail

Audiophony DJazz Pro MIDI MAP Detail

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN 2.- OUT – EXIT – RELOOP)
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) ”Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- BRAKE

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , | Leave a comment

Akiyama Pulsar

HOW TO SET UP?

The system must to recognize your Akiyama Pulsar as Audio and MIDI device before configuring in DJ ProMixer.

CONFIGURE YOUR AUDIO SETTINGS

Akiyama Pulsar only requires download and install Akiyama Asio Driver.

Akiyama ASIO

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Akiyama Pulsar as Audio Sound Card.

Akiyama Pulsar Audio

Akiyama Pulsar conections

For Internal Mode choose your output: 1.- for ¼ TSR connectors (balanced)  or 2.- for RCA (unbalanced).

Important: Akiyama Pulsar is designed to be used in internal mode (with internal Sound Card), but you can use also with DJ ProMixer in external mode (with other/s Sound Card/s and external mixer).

 MIDI CONFIGURATION

Akiyama Pulsar MIDI

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (PULSAR) and select on the right side AKIYAMA PULSAR.XML.
MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP
(Overview)

Akiyama Pulsar MIDI MAP
(Click to enlarge)

Akiyama Pulsar MIDI MAP Detaill

  1.- PLAY/ PAUSE
  2.- CUE
  3.- MANUAL LOOP (1.- IN  2.- OUT – EXIT – RELOOP) 
  4.- AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS) “Active” 1/2, “Del” X2
  5.- CUP (Cue and Play)
  6.- KEYLOCK
  7.- EFFECTS DIRECT BUTTONS FX 1, FX2, FX3  
  8.- MEMORY CUE / LOOP (1,2,3,4)
  9.- SAMPLES (1,2,3,4)
10.- FX SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK (A AND B)
16.- BROWSER (PLAYLIST, GROUPS, EXPLORER), OPEN CLOSE FOLDERS
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH

info mapping                    info PDF

Posted in Compatible Hardware | Leave a comment

Numark N4

HOW TO SET UP?

The system must recognize your Numark N4 as Audio and MIDI device before configuring in DJ ProMixer.

AUDIO SET UP

For Internal Mode choose your output: 1.- for XLR connectors (balanced)  or 2.- for RCA (unbalanced) or Booth.

Important: Numark N4 is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (N4) and select on the right side NUMARK N4.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

(Click to enlarge)

Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   SELECTOR OFF : MANUAL LOOP (1.- IN  2.- OUT  3.-  EXIT / RELOOP)
4.-   SELECTOR ON:  AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)(1.-MOVE DOWN    2.- IN  EXIT / RELOOP IN 3.-MOVE UP)
5.-   SELECTOR OFF: MEMORY CUE/LOOP  (1,2,3)
6.-   SELECTOR ON: FX 1, FX 2, FX 3
7.-   CHANGE PITCH RANGE (4%, 8%, 10%, 12%, 32 %)
8.-   KEYLOCK
9.-   ENABLE WHEEL VINYL MODE
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- AUDIO SOUNDCARD CONTROLS
14.- TRACKLIST SCROLL
15.- LOAD DECK
16.- BRAKE
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH

IMPORTANT: This MIDI Map enables two Mixer´s Channels (1 and 2), Channels 3 and 4 are disabled.

SELECTORS DETAIL

NEW:

In this MIDI Map there are included two buttons as “Selectors”:

1.- “FX Auto Tap” when is turn off it enables Memory CUE /loop for FX Buttons, when is turn on it enables Effects.

2.- “Blank Loop Button” when is turn off it enables Manual Loop (In, Out, Exit/Reloop), when is turn on it enables Auto Loop (Move Down,  In / Out /Exit / Reloop, Move Up).

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , , | Leave a comment

Denon DN MC 3000

HOW TO SET UP?

The system must recognize your Denon DN-MC3000 as Audio and MIDI device before configuring in DJ ProMixer.

Denon DN-MC 3000 only requires download and install Denon DJ Asio Driver, once installed you can configure it in DJ ProMixer.

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Denon DN-MC3000 as Audio Sound Card.

AUDIO SET UP

For Internal Mode choose your output: 1.- for ¼ TSR connectors (balanced)  or 2.- for RCA (unbalanced).

Important: DN-MC3000 is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

 

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DN-MC3000) and select on the right side DENON MC3000.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   MANUAL LOOP (1.- IN  2.- OUT – EXIT – RELOOP)
4.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) IN  EXIT / RELOOP IN, MOVE WITH “-“ 1/2 AND “+” x2
5.-   SELECTOR CUE (1,2,3,4) CUE (5,6)
6.-   KEYLOCK
7.-   EFFECTS DIRECT BUTTONS FX 1, FX 2, FX3  / SAMPLES (1 to 4) BY SELECTOR (16)
8.-   CUE / LOOP MEMORY (4 DIRECT BUTTONS) CUE (1,2,3,4) CUE (5,6) BY SELECTOR (5)
9.-   MEMORY CUE / LOOP (SHIFT BUTTON)
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- ENABLE WHEEL VINYL MODE
14.- TRACKLIST SCROLL
15.- LOAD DECK
16.- SELECTOR FX (FX1, FX2,FX3) / SAMPLES (1,2,3,4)
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- TRACKLIST SELECTOR (PLAYLIST, GROUPS, EXPLORER) , OPEN CLOSE FOLDER IN TRACKLIST
26.- REC
27.- CHANGE FOCUS TREE
28.- CHANGE FOCUS TRACKS

info mapping                    info PDF

Posted in Compatible Hardware | Leave a comment

Pioneer DDJ Ergo

HOW TO SET UP?

The system must recognize your Pioneer DDJ- ERGO as Audio Device and MIDI Device before configuring in DJ ProMixer.

Pioneer DDJ Ergo requires download and install Pioneer Asio Driver and also udgrade your firmware.

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Pioneer DDJ-ERGO as Audio Sound Card.

AUDIO SET UP

For Internal Mode choose your output (1.- for 1/4 TSR connectors or 2.- for RCA)

Important: Pioneer DDJ -ERGO is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI SET UP

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DDJ ERGO MID) and select on the right side PIONEER DDJ-ERGO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

Overview

(Click to enlarge)

Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   MANUAL LOOP (IN – OUT)
4.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS) PUSH: 1.- AUTO MODE: IN  EXIT / RELOOP IN     2.- MANUAL MODE: EXIT / RELOOP IN
5.-   VINYL MODE
6.-   KEYLOCK
7.-   EFFECTS DIRECT BUTTONS (1, 2, 3) (ON DISABLED)
8.-   SAMPLER DIRECT BUTTONS (1, 2, 3, 4)
9.-   CUE / LOOP MEMORY DIRECT BUTTONS (1,2,3,4)
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- SAMPLER VOLUMEN
14.- TRACKLIST SCROLL
15.- LOAD DECK
16.- REC
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND
23.- SCRATCH
24.- SHIFT (SHIFT+VINYL=BRAKE)

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , , , , , , | Leave a comment

Numark Mixtrack / Pro

HOW TO SET UP?

The system must recognize your Numark Mixtrack / Pro as Audio Device (only Mixtrack Pro) and MIDI Device (for booth models) before configuring in DJ ProMixer.

CONFIGURATION

Numark Mixtrack has two different set up (for Internal or External Mode):

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your Mixtrack Pro as Audio Sound Card.

AUDIO SETTINGS

INTERNAL MODE (Master + Headphones)

For Internal Mode connect your output in (1) RCA  connectors (L+R) for Master Output.

Connect your headphones in front ( ¼ TSR stereo connector).

EXTERNAL MODE (Deck A + Deck B connected to external mixer)

For External Mode connect your outputs 1.- RCA  connectors (L+R) for Deck A, and  2.- RCA connectors (L+R) for Deck B.

Important: Numark Mixtrack Pro is designed to be used as internal mode (with internal Sound Card using master output  & headphones) or external mode (using the internal soundcard for each deck).

Numark Mixtrack have not soundcard, it´s only MIDI Controller.

MIDI SET UP

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (MixTrack Pro) and select on the right side NUMARK MIXTRACK PRO.XML. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI MAP

Overview

(Click to enlarge)

Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   SELECTOR OFF : MANUAL LOOP (1.- IN  2.- OUT
EXIT / RELOOP)
4.-   SELECTOR ON:  AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)(1.-MOVE DOWN    2.- IN  EXIT / RELOOP IN 3.-MOVE UP)
5.-   SELECTOR ON: MEMORY CUE/LOOP  (1,2,3)
6.-   SELECTOR ON: FX 1, FX 2, FX 3
7.-   STUTTER
8.-   KEYLOCK
9.-   ENABLE WHEEL VINYL MODE
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- FOLDER / FILES SELECTOR
14.- TRACKLIST SCROLL
15.- LOAD DECK
16.- BEND (BUTTONS)
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- SCRATCH

SELECTORS DETAIL

DJ ProMixer Numark Mixtrack Selectors Detail

NEW SELECTOR´S FEATURES:

In this new MIDI Map there are included three buttons as “Selectors”:

1.- “Delete” and “Effects” buttons are connected for enable “Hot Cue” buttons (1,2,3) When “Delete” button is turn on it enables Memory CUE /loop for FX Buttons, when is turn on “Effects” it enables Effects (FX1, FX2, FX3).

2.- “Manual” button when is turn off it enables Manual Loop (In, Out, Exit/Reloop), when is turn on it enables Auto Loop (Move Down,  In / Out /Exit / Reloop, Move Up).

NEW:  FOLDER / FILES SELECTOR

Back Button select Folder / Files into the Browse.

info mapping     info PDF

Posted in Compatible Hardware | Tagged , , , , , , , , , | Leave a comment

Pioneer CDJ – 400

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 400

DJ ProMixer CDJ 400 Map

1.-    PLAY/ PAUSE
2.-    CUE
3.-    SEARCH CUE / LOOP POINT
4.-    MANUAL LOOP (IN – OUT – EXIT /
RELOOP)
5.-    AUTOLOOP FROM ¼ TO 32 BEATS (STARTS
IN 4 BEATS)
6.-   LINK TO PC
7.-   SCROLL / LOAD / ENTER
8.-   REVERSE
9.-   SYNC
10.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
11.- KEYLOCK
12.- PITCH
13.- BEND
14.- SCRATCH (WHEEL)
15.- CUE / SAMPLES / EFFECTS / LOOPS SELECTOR
16.- CUE / SAMPLES / EFFECTS /LOOPS DIRECT BUTTONS
17.- CHANGE FOCUS TREE / TRACKLIST
18.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER

19.- CHANGE DECK (ONLY IN DUAL MODE)

IMPORTANT: TO CONNECT 2 PIONEER CDJ-400 YOU NEED A HIGH SPEED CPU

info mapping     info PDF

Posted in Compatible Hardware | Tagged , , , | Leave a comment

Pioneer CDJ – 350

HOW TO SET UP?

– Single or dual mode (two or one CDJ´s)
– Audio configuration

DJ ProMixer CDJ - XDJ Set Up

PIONEER CDJ – 350

DJ ProMixer CDJ-350 MAP

1.-   PLAY / PAUSE
2.-   CUE
3.-   SEARCH CUE / LOOP POINT
4.-   MANUAL LOOP (IN – OUT – EXIT / RELOOP)
5.-   AUTOLOOP FROM ¼ TO 32 BEATS (STARTS IN 4 BEATS)
6.-   LINK TO PC
7.-   SCROLL / LOAD / ENTER
8.-   SYNC
9.-   SCRATCH (BUTTON)
10.- CHANGE TEMPO RANGE (4%, 8%, 10%, 12%, 16%, 32%)
11.- KEYLOCK
12.- PITCH
13.- BEND
14.- SCRATCH (WHEEL)
15.- CHANGE FOCUS TREE / TRACKLIST
16.- CHANGE FOCUS PLAYLIST / GROUPS-SUBGROUPS / EXPLORER
17.- CHANGE DECK (ONLY IN DUAL MODE)
18.- POWER ON / OFF

IMPORTANT: TO CONNECT 2 PIONEER CDJ-350 YOU NEED A HIGH SPEED CPU

info mapping                    info PDF

Posted in Compatible Hardware | Leave a comment

Denon DN – MC 6000

HOW TO SET UP?

The system must recognize your Denon DN-MC 6000 as Audio and MIDI device before configuring in DJ ProMixer.

Denon DN-MC 6000 only requires download and install Denon DJ Asio Driver, once installed you can configure it in DJ ProMixer.

Open DJ ProMixer and go to “Config” and open “Audio Setup”, here you can select your DN-MC6000 as Audio Sound Card.

CONFIGURE YOUR AUDIO SETTINGS

For Internal Mode choose your output (1.- for XLR connectors or 2.- for RCA) Others additional outputs 3.- Booth / Send Out 4.- Rec Out

Important: DN-MC6000 is designed to be used as internal mode (with internal Sound Card), but you can use also with DJ ProMixer as external mode (with other/s Sound Card/s and external mixer).

MIDI CONFIGURATION

MIDI MAP MC-6000

In “Config” go to “MIDI Controllers” and then select in MIDI PORT / MIDI MAP 1 on the left side one device (DN-MC6000) and select on the right side DENON MC600.XML. IMPORTANT: You have two maps to choose for channels 1-4 or channels 2-3. MIDI PORT / MIDI MAP 2: Nothing Selected.

MIDI  MAP

  (Click to enlarge)

                                                                  Detail

1.-   PLAY / PAUSE
2.-   CUE
3.-   MANUAL LOOP (1.- IN  2.- OUT – EXIT – RELOOP)
4.-   AUTOLOOP FROM ¼ TO 34 BEATS (STARTS IN 4 BEATS) IN  EXIT / RELOOP IN , MOVE WITH “-“ 1/2 AND “+” x2 (With Autoloop active also with << >> 13)
5.-   SELECTOR CUE / LOOP – SAMPLES
6.-   KEYLOCK
7.-   EFFECTS DIRECT BUTTONS EFX 1, EFX 2, FX3
8.-   CUE / LOOP MEMORY (4 DIRECT BUTTONS) 8.- (+SELECTOR) SAMPLER DIRECT BUTTONS (1, 2, 3, 4)
9.-   MEMORY CUE / LOOP (SHIFT BUTTON)
10.- FX ECHO BEAT SYNC (FROM 2/1 TO 1/8 BEATS)
11.- FX DRY / WET
12.- FX PARAMETER
13.- MOVE WITH ACTIVE FUNCTION (CUE/LOOP MEMORY  OR ACTIVE AUTO LOOP)
14.- TRACKLIST SCROLL / CHANGE FOCUS
15.- LOAD DECK
16.- CHANNEL SELECTOR
17.- PFL
18.- ROTARY KNOBS OF THE MIXER (GAIN, HI, MID,BASS)
19.- DECK´S VOLUMEN CONTROLS AND CROSSFADER
20.- PITCH
21.- SYNC
22.- BEND (WHEEL)
23.- BEND (BUTTONS)
24.- SCRATCH
25.- TRACKLIST SELECTOR (PLAYLIST, GROUPS, EXPLORER)
26.- REC
27.- CHANGE FOCUS TREE
28.- CHANGE FOCUS TRACKS

info mapping                    info PDF

Posted in Compatible Hardware | Tagged , , , , , , , , , , | Leave a comment